#CISCO NETWORK BOOSTER PASSWORD#

Disconnect the Access Point’s/Router’s antennas. With your Access Point/Router powered off, place the Wireless Signalīooster on top of the Access Point/Router.ī. Connect the antennas to the Wireless Signal Booster’s antenna ports.Ī. Again, just make sure that the SSID and passwords match the settings on your existing router.Connecting the Wireless Signal Booster toĭ. Most modern extenders will have settings for both a 2.4GHz network and a 5GHz network. Once it’s logged in and the connection is stable, it will rebroadcast the same data connection on the same SSID throughout your home, allowing for easy connections via other devices. What’s happening is that the extender is logging into your network via the router, just like you do with your laptop or phone.

#CISCO NETWORK BOOSTER PASSWORD#

But if it doesn’t (for example, if you bought your extender used), here’s what you do: Michael Crider/IDGįind the Wi-Fi settings page for your extender, and enter the same name for the SSID and password as you use with your Wi-Fi router. Once you’re logged into the repeater interface, it should start a wizard to guide you through connecting to your local network step-by-step. If the default name and password don’t work, try a factory reset of the device, which usually needs a button pressed with a pin or paperclip. Don’t worry, you can change them later in the extender settings menu. These are usually “admin” and “password,” respectively.

Once you get to this page, you’ll need to log in with the default username and password. If you can’t find it, Google your repeater brand on your phone and add “login,” and you’ll probably find it soon enough. My Netgear extender uses “some Asus models use “,” et cetera. If neither of those addresses work, check the instructions that came with your extender or the sticker printed on its side some brands use something a little different. Try entering both of those in the URL bar a login prompt should appear. The address for this interface is usually a simple numerical address on the local network, either 192.168.0.1 or 192.168.1.1. You’re going to use the browser to enter the extender’s web-based interface. On your computer, open a web browser like Edge or Chrome. If there’s a switch on the side of your extender, make sure it’s set to “Extender” mode, not “AP” or “Access Point.” (AP is for connecting directly to your modem, which you don’t need if you have a Wi-Fi router already, or an all-in-one modem/router.) It may need a few minutes to boot up. Note that in both cases you’ll temporarily lose web connection. Alternately, disconnect from your home Wi-Fi network and connect directly to the extender. Plug the extender into the wall, then plug the Ethernet cable into both the extender and your computer. Michael Crider/IDGĬonnecting a laptop to the Wi-Fi extender. (One probably came in the box with your extender.) If your computer doesn’t have an Ethernet port, you’ll need to connect to the default Wi-Fi network that the extender broadcasts, which is different from the one already in your home (at least for now.) This is usually “WIFI_EXTENDER” or something similar check the instructions if it asks for a password. You’ll need a desktop or laptop with an Ethernet cable for a wired connection, and the cable itself. If you want to connect to the extender over Ethernet (see the Connection section), you might have to fudge it and go farther. If you’re using a Wi-Fi extender for just one user (say, to get a better signal for a home office PC), you’ll want to place it approximately between that user and the Wi-Fi router. This outlet is in the middle of my halfway, between the router in the living room and the bedrooms. This will give it a fairly reliable, line-of-sight connection to the router, while rebroadcasting its wireless signal to the rooms on the second floor. Ideally you want it close enough to your Wi-Fi router at the source to get the most stable connection, but far enough away that it will cover a large area that the router doesn’t cover.įor example: if you live in a two-story house and your router is on the main floor in the living room, an ideal spot for the extender is plugged into an outlet at the top of the stairs.

Where to put your Wi-Fi extenderĬhoosing where to place your network extender is essential. But you’ll be paying for something that you don’t really need, since the extender won’t be able to speed up the connection from the router itself.

You can buy an extender that’s newer and/or faster than your router, and it will work fine.

Cisco network booster